A Sansui receiver differs from the other receivers and has some specifications that are different. For example, the receiver holds power up to 26 watts and is damaged if connected to devices that use more power. The device exists in analog form but advances with time.
The device has pure power with high quality and performance. Its cost is priced medium FM and AM, which are accurate and stable. Many people prefer using it due to its benefits, such as being cheap and requiring less space.
Luckily, the article provides a review concerning the Sansui g3000 receiver together with its advantages. Also, it shows the pros, cons and tips to consider before buying a new or a replacement Sansui g3000 receiver.
Features and benefits of Sansui g300 receiver
The Sansui G-3000 device is a low-cost AM/FM receiver featuring a highly accurate tuner and a highly steady amplifier section. The device has the following feature;
Frequency response: The receiver responds with a frequency that ranges from 10 hertz to 50khz. The frequency response produces a clear and compelling sound that can suit the user. Also, it has AUX ports using the AUX cables. For FM, the frequency range is 88 to 110 MHz, while the frequency range of the AM ranges from 530 to 17,000 kHz.
Input sensitivity: Sansui’s input sensitivity exists in any form. For instance, the sensitivity starts from 2.5 mV, 8 mV mic, 150 mV line and 150 mV DIN.
Measurements: the measurements of the device are taken in the form of inches, mm, weight in kilos and weight in pounds. The measurement in inches include; 13.86 (d) * 17.05 (w)* 6.02 (h), and in millimeters, they include; 153 (h) * 352 (d) * 433 (w). The Sansui device weighs 8.0 kg.
Display: The device displays information in analog form, not including the zeros and some tuning range of LW, FM and MW.
Power requirements: The device can hold power up to 80 watts (40 + 40) = 1 KHz. The constant power requirements are 4 ohms and 8 ohms. The 4 ohms support 1 kHz while the 8 ohms support 20 to 22,000 Hz and 1 kHz, around 52 watts. The power per channel required is 26 watts in an 8-ohm stereo.
Speaker resistance: It supports the resistance ranging from 4-ohms to 8-ohm impedance.
Channel differentiation: The Sansui device separates channels ranging from 50 DB to 95 DB. The 50 DB is the MM, while the 95 DB is the line.
Noise to signal ratio: The ratio between the noise and the signal is 95 DB line and 75 DB MM, respectively.
General harmonic distortion: The device distortion is approximately 0.15% for mono and 0.2 for stereo. The harmonic distortion is rated as an output distortion.
Signal strength: The device’s signal strength is usually measured in meters where 1 is for YES, and 0 is for NO. when it comes to the center tuning meter; still, 0 is for NO and 1 is for YES.
Damping factor: The device damping factor is around 30, and the device has speaker outputs that are 2 * 2 speakers and a phone.
Sound: The device has bass and treble sounds.
Factors to consider when buying Sansui g300 device
- Power
Power impacts how straightforward and a receiver may deliver powerful sound. Even at low and medium volumes, a high-wattage receiver gives superior sound quality than one with less power. The Sansui receiver must have adequate power to support both the speakers it’s connected to and the room in which it’s installed. Speakers with a lower sensitivity demand more power.
- Interface
A greater Sansui receiver with an easy-to-use display screen might mean the difference between listening to stadium-quality noise and seeing your pricey system gather dust because you can’t figure out how to switch it on. It’s crucial to play around with the display while looking at receivers to ensure you can explore it and learn all of the capabilities.
- Calibration
The Sansui receiver can detect speaker size, calculate the distance between each speaker and listener, and verify if the parts are correctly configured by sending test tones to the speaker and amplifier and hearing the sound using a microphone.
you may read also our another comprehensive review of Appj mini2013 6j1+6p1
Frequently asked questions:
- How much does the Sansui g3000 receiver cost?
The Sansui g3000 stereo receiver costs $ 200.00. but, if there is any shipping activity, the price increases by $50.00, and the total becomes $ 250.00. The shipping cost varies depending on the place and the distance.
Conclusion
The Sansui g3000 receiver is essential in that it has an accurate tuner and an amplifier that provides quality and a good sound when connected with other recommended devices. Many people wish to buy such a receiver, and the information above summarizes the whole product, including its drawbacks.
Moreover, when choosing the receiver, it is essential to consider various factors to obtain the best receiver that can last longer. Also, take precautions when using the receiver, such as cleaning it often, removing any dust present, and solving any early detected issues.